AT45DB161E-MHD-T

Les images sont à titre de référence seulement

AT45DB161E-MHD-T

IC FLASH 16MBIT SPI 85MHZ 8UDFN

100% original & Nouveau

24 heures prêtes à expédier

Garantie 365 jours

RFQ et Obtenez plus de rabais

Spécifications

Supplier Dialog Semiconductor GmbH
Package Tape & Reel (TR)
ProductStatus Not For New Designs
MemoryType Non-Volatile
MemoryFormat FLASH
Technology FLASH
MemorySize 16Mb (528 Bytes x 4096 pages)
MemoryInterface SPI
ClockFrequency 85 MHz
WriteCycleTime-WordPage 8µs, 4ms
Voltage-Supply 2.5V ~ 3.6V
OperatingTemperature -40°C ~ 85°C (TC)
MountingType Surface Mount
Package/Case 8-UDFN Exposed Pad

Vue d'ensemble

Description

AT45DB161E-MHD-T is a 16‑Mbit Serial DataFlash memory from Atmel/Microchip. It provides non-volatile storage for embedded systems and is accessed over a Serial Peripheral Interface (SPI).
Key points
- SPI-compatible interface with commands for read, write, erase, and status.
- Two internal data buffers plus page-level programming and sector/block erase.
- Random read capability with 3-byte addressing; supports fast/continuous read modes.
- Features such as a status register (busy flag), deep power-down, and hardware write protection.
- RoHS-compliant, typically available in an 8-pin MHD-T package (package and reel details vary by supplier).
Typical use
- Store firmware, configuration, logs, or data for microcontroller systems.
- Efficient data updates by buffering data in internal buffers and then writing to flash (BUFFER WRITE followed by BUFFER-TO-PAGE).
Note
- Check the datasheet for exact page sizes, erase block sizes, timing, and the specific packaging/temperature details for your lot.

Features

Here are the key features of AT45DB161E-MHD-T (16‑Mbit Serial DataFlash):
- 16 Mbit (2 MBytes) serial DataFlash with SPI interface
- SPI-compatible interface with CS, SCK, SI, SO; supports standard and continuous read
- Page-based memory with two internal data buffers for buffered writes
- Flexible erase: page erase, block/sector erase, and chip erase
- Read/Write operations with Ready/Busy status; fast programming via internal buffers
- Endurance and retention: typical ~100k P/E cycles; data retention ~20 years
- Low‑power modes including Deep Power-Down
- Supply voltage: typically 2.7–3.6 V
- Operating temperature: industrial range (typical -40°C to +85°C)
- Packaging: compact 8‑pin package; MHD‑T denotes available tape-and-reel/packaging variant
Note: exact page size, block sizes, and timings are specified in the datasheet for the device revision.

Package

8-pin Small Outline Integrated Circuit (SOIC) package, Tape‑and‑Reel (T).

Pinout

- Pin count: 8 pins.
- Function: 16-Mbit Serial DataFlash memory (SPI interface). It provides non-volatile storage with an SPI-compatible interface (CS, SCK, SI, SO) plus WP and HOLD, plus VCC and GND.

Manufacturer

Manufacturer: Atmel Corporation (now part of Microchip Technology). Type of company: A semiconductor company that designs and manufactures integrated circuits, including memory devices (DataFlash) and microcontrollers.

Application

Applications of AT45DB161E-MHD-T (16‑Mbit SPI DataFlash):
- Embedded systems: firmware storage, bootloaders, and configuration data
- Data logging: industrial, environmental, medical sensors (event logs, history)
- Caching/buffering: high‑speed data streams (audio, video capture, image sensors)
- Consumer electronics: cameras, MP3 players, handheld devices
- Automotive/industrial instrumentation: non‑volatile storage for logs and parameters
Note: uses SPI serial interface with page/block erase for reliable data storage.

Equivalent

The AT45DB161E-MHD-T is a 16‑Mbit Serial DataFlash (256B page, 8‑pin SOIC). Exact 1:1 cross references are rare, but near equivalents (16‑Mbit SPI devices) from other vendors include:
- Winbond W25Q16BV
- Macronix MX25L1615D
- GigaDevice GD25Q16C
- ISSI IS25LP016D
- Spansion/Cypress S25FL016K
Note: these are SPI Flash/DataFlash devices with different command sets; verify compatibility and timing before replacement.

Expédition

Méthodes d'expéditionNous

offrir des services d'expédition mondiaux par DHL, FedEx, TNT, UPS ou tout autre expéditeur de votre choix.


Référence des frais d'expédition (DHL/FedEx):

DHL: Les frais d'expédition vont de 25 à 45 $ (0,5 kg), avec un délai de livraison estimé de 2 à 5 jours ouvrables.

FedEx: Les frais d'expédition varient de 25 à 40 $ (0,5 kg), avec un délai de livraison estimé de 3 à 7 jours ouvrables.

UPS: Les frais d'expédition vont de 25 à 45 $ (0,5 kg), avec un délai de livraison estimé de 3 à 7 jours ouvrables.

TNT: Les frais d'expédition varient de 25 à 65 $ (0,5 kg), avec un délai de livraison estimé de 3 à 7 jours ouvrables.

EMS: Les frais d'expédition varient de 30 à 50 $ (0,5 kg), avec un délai de livraison estimé de 7 à 15 jours ouvrables.

Courrier aérien enregistré: Le coût d'expédition est de 2 à 4 $ (0,1 kg), avec un délai de livraison estimé de 5 à 20 jours ouvrables.

Paiements

Payment Methods

Le terme de paiement est 100% prépayé.

Actuellement, nous n'acceptons que les méthodes de paiement ci-dessous:

1. PayPal

2. Carte de crédit/débit

3. Transfert bancaire

Similaire